KENWOOD TK 360G PROGRAMMING SOFTWARE MANUAL
KENWOOD TK 360G PROGRAMMING SOFTWARE SOFTWARE

A good example is if you have programmed CTCSS or DCS options in the SAT (subaudible tones) you need to enable their transmission, with the SCTP instruction after the TXM instruction in the Encode PTT-Press script. Check out the Kenwood documentation in the section below. This sets the modulation source to be the microphone. When the PTT button is pressed, the script (here called TXPRESS) is run. Then select the script you created above: Use Insert key to get list of scripts. Use the up/down arrows to select Encode PTT-Press. From the Main menu > System parameters > F2. You next need to assign this to the PTT press (right image). TXM enables the TX Mic audio вЂ“ This fixes the problem with no TX audio. Under Advanced Options > Encode formats: F4 and F5 go through scripts. This is probably due to the Encode Scripts (left image). Encode ScriptsДЄ common problem reported is that when pressing PTT, the radio transmits a carrier but no audio. You may need to tweak the receiver tuning to improve sensitivity. Re-start the program and the frequency range will have changed. When you find the radio in the message file, you will need the frequency range label and the minimum and maximum frequency. Inside the HEX editor, search for the radio model. Open this with your preferred HEX editor. Inside your standard file browser, locate the programвЂ™s вЂњ.msgвЂќ file, for KPG-20D called вЂњKpg-20d.msgвЂќ. This process holds for other models of radio too. The two images show the TK-709 T frequency range has been modified from 150-170 MHz to 140-170 MHz, thus covering the 2 metre amateur bands. This is easily rectified by editing the programвЂ™s вЂњ.msgвЂќ file.

KENWOOD TK 360G PROGRAMMING SOFTWARE SOFTWARE

* Press F5 to program the radio via the TransLink cable.Д«ecause Kenwood make Amateur Radio equipment as well as commercial, the software will not (as standard) accept frequencies in the amateur radio bands.Return to Basic level KPG-20D from Main menu.Have a look around, using the help ( F1) to see if you can tweak anything.Under Main menu > Advanced options > Configuration you can select the TransLink port (the programming cable port), Licencing information, and the like.From Main menu > Advanced options, you can select either Keys, microphone or Keys, front panel to set microphone and front panel button functions.

* clk allows for the clock frequency of the radios CPU to be moved to reduce possible interference.

* scan allows for individual channels to be include or exclude from a scan.

* SAT tx and SAT rx allow for CTCSS, DCS and SelCall to be set.

are the transmit and receive frequencies in MHz (if you cannot enter the frequency you want, see below) This may be alphanumeric or numerical, depending on Main menu > Setup radio > Channel readout mode

* The ds column is the string appearing on the screen for the given channel.

* The ch column is the channel number, and it determines the channel order.

My datafile (with program from above) is called M1GEO_70.DAT So this small section aims to outline basic functionality.ДЇrom the Main menu, enter the Basic level KPG-20D.

KENWOOD TK 360G PROGRAMMING SOFTWARE MANUAL

I wasnвЂ™t able to find a manual for this program though there is apparently one. The usage of this software is quite complex. The end column of the list above will show you what version of the program you need. If this is not the case, I will remove this software immediately. I could not find a manual or an EULA for the software вЂ“ I have assumed it is freely distributable. These programs, Kenwood KPG-20D and Kenwood KPG-67D programming software, seem to be freely availiable and various people are distributing it freely. They will program the following radios: Model Sorry this page is still being written, and may appear a bit confusing.There are two versions of the Kenwood Programming Software (KPG-20D and KPG-67D) on this page.

This page details the conversion and programming of some of the Kenwood PMRs available on the second hand market.

Kenwood tk 360g programming software